Your region
 
Tel.  888-206-4377
info@noisemeters.com
Home > Products > Noise Dosimeters > dBadge > dBadge2 PRO Noise Dosimeter >Specifications

dBadge2 PRO Noise Dosimeter - With Audio and Octave Bands

dbadge2 Pro Noise Dosimeter with audio recording and octave band filters

Technical Specifications

For occupational noise and hearing protection applications, it is essential that the dosimeter you use meets the correct standards. The dosimeter standards are based on the sound level meter standards ANSI S1.4 and IEC61672, but are specific to this particular application. The relevant standards are:

  • ANSI S1.25 Personal Noise Dosimeters
  • IEC 61252 Personal Sound Exposure Meters

The dBadge2 PRO meets and exceeds these standards. It is suitable for occupational noise assessments in line with the USA and Canadian regulations, European regulations, UK HSE guidelines, Australian, New Zealand and any other regulations we are aware of.

As many parameters are configurable, the dBadge2 should be able to satisfy any regulations. If you are unsure then please contact us and we will check it out for you.

Acoustic  
Standards ANSI S1.25:1991 R2007, IEC 61252 Ed 1.1 (2002-3)
Linear Operating Range 55 to 140.3 dB(A) RMS
Dynamic Range 96dB
Peak Measurement Range 90 to 143.3 dB (C or Z weighted)
Sound Exposure Range 0.0- 6,100.0 Pa²Hours
  0.00 – 22,000,000.00 Pa²Sec
  0.0-100,000.0% Dose
Frequency Weightings A, C and Z
Time Weightings Fast, Slow and Impulse
Exchange Rate Q=3 or Q=5
Threshold 70 to 90 dB in 1 dB steps (set using Insight software)
Criterion Level 70 to 90 dB in 1 dB steps (set using Insight software)
Stabilization Time <3 seconds after power up
   
Measurements  
All measurements are stored. The selection of parameters to display does not restrict the storage.
Measurement Summary Lavg, LAeq, LCeq
TWA (8hr), Projected TWA (8hr)
LEP,d, LEX,8hr
Dose%, Projected Dose %
LApk + Time, LCpk + Time, LZpk + Time
PA²Secs, PA²Hours
LAS exceedance time
LC-LA (for HML calculations)
LCpk >135 (count), LCpk > 137 (count), LCpk > 140 (count)
LAFmax + time, LAFmin + time
LASmax + time, LASmin + time
LAImax + time, LAImin + time
Cumulative motion index (% of time motion detected)
Time History Profile Each parameter stored every second
TWA (8hr), Projected TWA (8hr)
LAeq, LCeq
LCpk, LZpk
LAFmax, LASmax
Motion Index (0 or 1)
Audio Events Trigger sources: LAF, LAS, LCpk, LZpk
Sampling rate: 8kHz, 16bit
Recording time: 10 seconds with 3 second pre-trigger
Audio Notes 15 seconds for each measurement run
Octave Band Filters Nine Octave Bands: 31.5Hz to 8kHz
A or Z weighted Leq and LMax (Fast or Slow)
   
Technical  
Battery Internal NiMH, 800mAH
  Typically 35 hours using Broadband Mode
  Typically 15 hours using Octave mode
Charge Time <6 Hours from fully discharged
PC Interface USB 2.0 Full speed 12Mbps via Docking Station
Bluetooth Connectivity Bluetooth 4.0 (Low Energy or Smart)
TX Power: 0 dBm to -23 dBm
Receiver sensitivity: -93 dBm
Range: Typically 25m line-of-sight
Display 96 x 64 dots, full color OLED with adjustable contrast
User Controls Two buttons. Remote control via Airwave application
   
Memory  
Maximum Run Duration 24 hours
Maximum number of Runs 100
Storage Capacity Internal USD Flash memory - 300 hours of run data (including 1 second profile data)
  Up to 90 minutes of event audio recording
   
Environmental  
Operating Temperature Range 0°C to +40°C (for <±0.5dB error limit)
  -10°C to +50°C (for <±0.8dB error limit)
Ambient Pressure Range <±0.5dB over 85 - 112kPa
Humidity range <± 0.5dB over 30% - 90% (non-condensing)
I.P. Rating IP65 (with permeable air vent)
   
Physical  
Dimensions 85L x 54W x 55H mm
Weight 117g, 4.13oz
Construction Materials Plastic Case/ Charger - PC/ABS
  Mounting Clips - POM
  Gasket - Silicone
  Display window - Acrylic
  Foam Windscreen - Polyester foam
  Microphone - Brass / Nickel

 

dBadge2 Datasheet (PDF, 789k)

DB2PROK1
$2576.00
dBadge2 PRO kit with 1 dosimeter, Calibrator, Software and Case
In stock
DB2PROK3
$5552.00
dBadge PRO kit with 3 dosimeters, Calibrator, Software and Case
In stock
More pricing information

dBadge Range

dBadge2
dBadge2
Noise Dosimeter
From $2018.00
dBadge2 PLUS
dBadge2 PLUS
With Audio Recording
From $2266.00
dBadge2 PRO
dBadge2 PRO
Audio Record & Octaves
From $2576.00
noise at work sound level meter

Combination Kits

Hand held meter and personal dosimeters

More details...

How to Buy

Credit Card
Click the button or call 888-206-4377.

Purchase Order
To: info@noisemeters.com
Or by fax: 888-584-2230.

Information Request




Prices and Ordering

Kits contain dBadge2 PRO Dosimeters with Audio and Octave Band Filters. Kit has dBadges, Calibrator, Dock/Charger, Peli Case and Software.
Kits with 1, 2, 3 and 5 dBadges have one 3-way charger. Kits with 10 dBadges have two 3-way chargers.

Order Code
Description
Purchase
Price (USD)
 
DB2PROK1
Kit with 1 dBadge2 PRO Dosimeter, Calibrator, Charger, Software and Case
$2576.00
In stock
DB2PROK2
Kit with 2 dBadge2 PRO Dosimeters, Calibrator, Charger, Software and Case
$4078.00
In stock
DB2PROK3
Kit with 3 dBadge2 PRO Dosimeters, Calibrator, Charger, Software and Case
$5552.00
In stock
DB2PROK5
Kit with 5 dBadge2 PRO Dosimeters, Calibrator, Charger, Software and Case
$8415.00
In stock
DB2PROK10
Kit with 10 dBadge2 PRO Dosimeters, Calibrator, Charger, Software and Case
$15502.00
In stock

 

Telephone 888-206-4377  
info@noisemeters.com  
Home - Contact - Applications - Products - Rental - News - Resources - Search - Help
Sound Level Meters - Dosimeters - Noise Signs - Microphones & Calibrators